SpeedyBee F405 WING APP Fixed Wing Flight Controller Support Ardupilot VTOL for RC Airplane Precise details: --Specifications: -Product Name:SpeedyBee F405 WING FC board MCU:STM32F405,168MHz,1MB Flash IMU(Gyro&Accelerometer):ICM-42688-P Barometer:SPL006-001 OSD Chip:AT7456E Blackbox:MicroSD Card Slot UART:6 sets(USART1, USART2, USART3, UART4, UART5, UART6(Dedicated for Wireless board Telemetry connection)) I2C:1x Used for magnetometer, digital airspeed sensor ADC:4x (VBAT, Current, RSSI, Analog AirSpeed) PWM:12x (11+ "LED" pad) ELRS/CRSF receiver:Supported,connected to UART1 SBUS:Built in inverter for SBUS input (UART2-RX) LED:3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red) 1x RGB RSSI:Supported,Named as RS . Supported FC Firmware: INAV:SpeedyBeeF405WING(default),ArduPilot: SpeedyBeeF405WING Weight:8.9g -Product Name:SpeedyBee F405 WING PDB board Input Voltage Range:7~36V (2~6S LiPo) Battery Voltage Sensor:Connect to FC board VBAT, 1K:10K (Scale 1100 in iNav, BATT_VOLT_MULT 11.0 in ArduPilot) Battery Current Sensor:90A continuous, 215A peak Connect to FC board Current (Scale 195 in iNav, 50 A/V in ArduPilot) TVS Protective diode:Yes FC BEC output Output:5.2V +/- 0.1V DC Continuous current 2.4 Amps, 3A Peak Designed for FC, Receiver, GPS module, AirSpeed module, Telemetry module, WS2812 LED_Strip VTX BEC output Output:9V +/- 0.1V DC Continuous current 1.8 Amps, 2.3A Peak Voltage adjustable, 9V Default, 12V or 5V via jumper Designed for Analog Video Transmitter,Digital Video Transmitter, Camera. Servo BEC output Output:4.9V +/- 0.1V DC Continuous current 4.5 Amps, 5.5A Peak Voltage adjustable, 4.9V Default, 6V or 7.2V via jumper Designed for Servos. Weight:11.4g -Product Name:SpeedyBee F405 WING Wireless board Wireless Configuration (long press BOOT button for 6 seconds to switch modes):BLE mode, connect to Speedybee APP Wireless Configuration (long press BOOT button for 6 seconds to switch modes):Wi-Fi mode, connect to QGroundControl APP, Speedybee APP, MissionPlanner, etc. Wireless Configuration (long press BOOT button for 6 seconds to switch modes):Classic Bluetooth SPP mode, connect to QGroundControl APP, MissionPlanner LED strip controller (short press BOOT button to switch effects, long press 2 seconds to switch modes):4x WS2812 LED strip connectors, adjustable colors and flashing modes LED strip controller (short press BOOT button to switch effects, long press 2 seconds to switch modes):Max 5.2V 1.3A, supports around 70pcs 5050 WS2812 LED beads On-board battery level indicator:4x RGB indicator LED for battery level display by number of lights Weight:4.2g -Package Included: 1x SpeedyBee F405 WING FC board 1x SpeedyBee F405 WING PDB board 1x SpeedyBee F405 WING Wireless board 1x SpeedyBee F405 USB extender 1x 90 Degree pin header(3x12) 3x Straight pin header(1x12) 1x White Straight pin header(1x4) 5x M2 x 12 copper Standoff Spacer 10x M2 x 4 small head cross screw 5x M3 x 4mm Silicone Grommets 1x 8pin SH1.0 USB extender cable(80mm) 1x 4pin SH1.0 Analog VTX cable(250mm) 1x 6pin SH1.0 GPS Module cable withou connector on another end(250mm) 1x 6pin Digital VTX cable(250mm) 1x 4pin SH1.0 to 3+2pin JST1.25FPV Cam cable(250mm) 1x 6pin GH1.25 Telemetry module cable(200mm) 1x 4pin Dupont single-head cable(150mm) 1x Double-sided tape for isolating pins and cables(32x9x1mm)