100% brand new and high qualityFeatures:Made of high quality material, solid, durable and good performance, long service life.A voltage regulator that no matter the input voltage is lower/higher than output voltage, the output voltage can be stable.It integrates analog adjustment and digital control, and shows the preset voltage/current/power and so on in real time.Large high definition LCD with 160wide viewing angle, easy and comfortable reading.It features both hardware and software protection, safe to use.The screen supports 4 way rotation, convenient to use.It also has night rest screen mode, suitable for any conditions.Smart temperature control fan, thickened radiator, 2 way ventilation, great cooling effect.It also can used as a common voltage Buck-Boost power supply with over-voltage/over-current/over power/over temperature/under voltage protection.With constant current function, it can charge the rechargeable battery within 0.6V-36V.Boost Step Down Converter only, other accessories demo in the picture is not includedSpecification:Material: ABS, Electronic ComponentsSize: app.7.9 x 4.2 x 4.1cm/3.11 x 1.65 x 1.61inColor: BlackQuantity: 1 PcProductParameters:Input Voltage: DC 6.0-36V(Limit low voltage 5.5V, limit high voltage 38V)Output Voltage: DC 0.6-36VOutput Current: 0.000A-5.000AOutput Power: 80WInput Current Limit: Max.7ACurrent Resolution: 0.001AVoltage Accuracy: 0.3% + 1 byteCurrent Accuracy: 0.4% + 3 byteCapacity: 0-999999AhEnergy: 0-999999WHTime: 0-1000 HoursHardware Protection: Output short circuit protection, short circuit without burning, output anti-backflow, can directly charge the rechargeable battery, without additional anti-backflow diode.Software Protection: Over voltage protection(OVP), over current protection(OCP), over power protection(OPP), over temperature protection(OTP),input under voltage protection(LVP), power chip self protection(OEP).Tips: Requirements for full load output power supply: input power supply optional 15-35V, power above 100WCharging Steps:1. Determine the floating charge voltage and charging current of your rechargeable battery; (if the parameter of lithium battery is 3.7V/2200mAh, the floating charge voltage is 4.2V; if it is 12V rechargeable battery, generally set the floating charge voltage to about 14V)2. Under no-load condition, set the output voltage to floating charge voltage; (if 3.7V lithium battery is charged, adjust the output voltage to 4.2V)3. Set the charging current (constant current value) and set the current directly.4. Connect the battery for charging.Tips: When charging the battery, the positive and negative poles of the battery should not be connected reversely, which is easy to burn the productTo drive the LED lamp:1. Determine the working current and maximum working voltage of the led you need to drive;2. Under no-load condition, set the voltage value and current value to make the output voltage reach the maximum working voltage and current of LED (Note: calculate the power when setting the current, charge within the power range, use over power, and the product will enter the protection state.)3. Connect led and test the machine.This product can adjust the constant current value (between 0 - working current) to realize the LED's stepless dimming and no stroboscopicDetails of interface and key functions:Short press the "ON/OFF" button to turn on and off the power output, long press the " ON/OFF" button for 2 seconds, the screen can rotate, 360 four-way rotation.Turn the encoding potentiometer to turn the page quickly.Press the code potentiometer key briefly to activate the parameter (voltage / current) to be set;Short press the key of the coding potentiometer to switch between full selection and bit selection;When all is selected, the blue display will be reversed, and the set voltage / current will be switched through the rotary encoder;After bit selection, the corresponding bit will be displayed in reverse blue, and parameters will be set by rotating encoder;After the setting is completed, long press the key of the encoding potentiometer for 2 seconds or more, and no key operation will automatically exit the setting;All parameters are saved automatically after exiting.Press the encoding potentiometer key for a short time, and select "capacity / energy / time" for all. After selecting all, the corresponding one will be displayed in reverse blue. Switch the parameters to be cleared by rotating the encoder. After selecting, press the encoding potentiometer key for a short time to clear the corresponding parameters. After selecting, press the encoding potentiometer key for a long time for 2 seconds or over 6 seconds, and the operation without keys will exit automatically.Press the key of codin