Features: 1.This temperature controller is equipped with a high accuracy sensor with accurate measurement data and stable performance. 2.The ABS flame retardant shell design is adopted on this incubator temperature controller, which can be more safe and reliable. 3.It is suitable for incubators, household refrigerators, household water heaters, greenhouse cultivation, and supermarket freezing equipment. 4.This incubator temperature controller is not only small in size, but also easy to operate and set in steps. 5.The measurement accuracy of 0.3C and the temperature measurement range of ?40 to 110C make this temperature controller stand out. Specification: Item Type: Incubator Temperature Controller Material: ABS Power Supply Voltage: AC110-230V Power Supply Frequency: 50/60Hz Temperature Measurement Range: -40-110 Temperature Measurement Accuracy: 0.3 Humidity Measurement Range: 0%-100%RH Humidity Measurement Accuracy: 3% Output Control: Relay Output Output Power: Mximum 10A Installation Hole Size: Approx. 28 x 70mm/1.1 x 2.8in Setup essential Start value Stop value (The program automatically determines that the working mode is cooling/dehumidifying mode) Heating/cooling mode setting Setting method: Setting (start temperature): long press the 1 button, the start temperature flashes, and set the start temperature value through the 11 key Setting (stop temperature): long press the 1 button to stop the temperature flashing, and set the stop temperature value through the 11 button. Heating use case: Control the water heater, stop heating to 70C, start heating again when the temperature drops to 45C, and cycle Step 1: Heating working mode, starting temperature stop temperature Step 2: Long press the 1 button, the start temperature flashes, and set the start temperature to 30 by pressing the 11 button Step 3: Long press the 1 button to stop the temperature flashing, and set the stop temperature to 25 through the 1 button, and the setting is complete! If there is no operation for 10 seconds, it will automatically return to the normal display state. You can also press 22 to exit immediately. Humidification/dehumidification mode setting Setting method: Setting (starting humidity): long press the 2 key, the start humidity value flashes, and set the start humidity value through the 22 key. Setting (stop humidity): Long press the 2 key to stop the flashing of the humidity value, and set the stop humidity value through the 22 key. Humidification example: To humidify the supermarket, control the humidifier to 50% RH to start humidifying, and to stop humidifying when humidified to 80% RH. Setting steps: Step 1: Long press the 2 key to start the humidity value flashing, and use the 22 key to set the start humidity value to 50%RH Step 2: Long press the 2 key to stop the humidity value flashing, and set the stop humidity value to 80%RH through the 22 key, and the setting is complete! Press the key for 10 seconds without operation, it will automatically return to the normal display state, or you can press the 11 key to exit immediately. Dehumidification example: Workshop control exhaust dehumidification system, humidity 75%RH starts dehumidification, humidity 45%RH stops dehumidification Setting steps: Step 1: Long press the 2 key to start the humidity value flashing, and use the 22 key to set the starting humidity value to 75%RH Step 2: Long press the 2 key to stop the humidity value flashing, and set the stop humidity value to 45%RH by pressing the 22 key, and the setting is complete! Press the key for 10 seconds without operation, it will automatically return to the normal display state, or you can press the 11 key to exit immediately. Temperature correction Temperature correction: Press the 11 key at the same time for 5 seconds to start the temperature digital flashing, and it will display 00. Set the start temperature correction value through the 11 key. After the setting is completed, press the button for 10 seconds without any operation, and it will automatically return to the normal display state. You can also press the 22 button t