Garage door signal light flashing light warning light strobe light open door indicator AC/DC 12-265V strong yellow light

¥36,390
+ 配送料¥1,099

Garage door signal light flashing light warning light strobe light open door indicator AC/DC 12-265V strong yellow light

  • ブランド: Unbranded

Garage door signal light flashing light warning light strobe light open door indicator AC/DC 12-265V strong yellow light

  • ブランド: Unbranded
希望小売価格: ¥46,790
価格: ¥36,390
得する金額: ¥10,400 (22%)
販売元:
¥36,390
+ 配送料¥1,099

在庫あり

以下の支払い方法を利用することができます

説明

AC/DC 12V-265V LED gate flashing light Lamp Alarm Lamp For swing sliding Gate Opener/Barrier Gate Signal strobe flashing lamp 1,Terminal 1 is for connectino thepower input; working voltage is 12-265VAC/DC. 2,Terminal 2 is for connecting the antenna of RF controller to extend the effective working distance Instruction After power the lamp on, LED will start fashing in 1HZ(default setting). sW1 is the switch for selecting flashing or on mode of the lamp.CAP short connectsthe 2 pins; the lamp is in flashing mode. Remove the CAP from 2 pins, the lamp is inon mode. Be Careful, the whole board includes the components are with high voltage. Alwaysmake sure power is off before you open the cover. Installation Open the package; take out the products and all the accessories. Removing the antenna by rotatinganticlockwise. Mark 2 holes on the wall by using the fixing hole of bracket. Drilling two 6mm diameter holes and one 10mm diameter hole. Then put the expansion plug intothe 6mm diameter holes. Put the wires through 10mm diameter hole. Put the power wire and antenna through the cable holes in the holder. And fix the holder to thewall by provided 4mm*30mm self-taping screws. Connect the wire and antenna to the correct terminals. Put the cover back and make sure the cover is fastened with the bottom base without any gap.Then screw the antenna up and turn clockwise to make it tight. Always install the holder and lamp upright to the ground. Horizontally installation may cause therain go inside the lam and damage the board. Specification Feature display Antenna This is used to extend the effective distance of controller Waterproof and dustproof It is made of plastic material IP 54 . Selecting flashing or steady lighting SW1 is the switch for selecting flashing or on mode of the lamp. CAP short connects the 2 pins; the lamp is in flashing mode. Remove the CAP from 2 pins, the lamp is in on mode. 12-265V AC/DC input
  • Fruugo ID: 231755588-495092597
  • EAN: 7382840710688

製品安全情報

以下に概説するこの製品に固有の製品安全性情報を参照してください。

以下の情報は、この製品を販売する独立したサードパーティ小売業者によって提供されています。

製品安全ラベル

CE Mark
安全上の警告: Not suitable for children under 36 months, Choking Hazard, Adult supervision recommended
材料: Polymethylsilsesquioxane

配送と返品

3日間以内に発送

  • STANDARD: ¥1,099 - 間の配達 木 09 10月 2025–水 15 10月 2025

中国より発送。

ご注文の商品は、お客様の仕様に従い、万全の状態で配送されるように最善を尽くしています。しかし、もし注文に抜けがあったり、注文したものと違う商品が届いたり、注文に満足できないその他の理由がある場合は、注文全体やその中のいずれかの商品を返品し、その全額の返金を受けることができます。 全額返金ポリシーを見る

製品コンプライアンスの詳細

以下に概説されているこの製品に固有のコンプライアンス情報を参照してください。

以下の情報は、この製品を販売する独立したサードパーティ小売業者によって提供されています。

製造業者:
次の情報は、Fruugoで販売される関連製品の製造業者の連絡先詳細です。

  • manufacturer_trading_name
  • Xiamen Cheering Industrial
  • Room 401, No. 35, Yuanshan North Lane, Huli District
  • Xiamen
  • CN
  • 361000
  • fruugo202204@163.com
  • 139 7376 5108

EUにおける責任者:
次の情報は、EUにおける責任者の連絡先情報の概要です。ここで言う責任者とはEUに拠点を置く指定経済事業者で、EU域内で販売される関連製品に関するコンプライアンス義務を負う者のことです。

  • Van Lavazza
  • Y & H S.R.L.
  • Via Gravina 21 MT matera
  • Puglia
  • Trani
  • IT
  • 75100
  • itlyhsrl@gmailcom
  • 0039 3917722149