In the installation location: For Kawasaki ER-6F 2012-2017 For Kawasaki ER-6N 2012-2017 For Kawasaki KLE650 2010-2017 For Kawasaki Ninja 250R (Fi model) 2013-2015 For Kawasaki Ninja 300 2013-2018 For Kawasaki Ninja 400R 2013- 2016 For Kawasaki Ninja 400 2018 For Kawasaki Ninja 650 2012-2016 For Kawasaki Ninja 1000 2011-2016 For Kawasaki Versys 650 2010-2018 For Kawasaki Versys 1000 2012-2018 For Kawasaki VN900 2011-2015 For Kawa Saki Vulcan S 650 2015-2018 For Kawasaki Vulcan 900 2011-2018 For Kawasaki W800 2011-2017 For Kawasaki Z300 2015-2016 For Kawasaki Z650 2017-2018 For Kawasaki Z750 2010-2012 For Kawasaki Z750R 2011-2012 For Kawasaki Z800 2013-20 17 For Kawasaki Z800e 2013-2017 For Kawasaki Z1000 2010-2016 For Kawasaki Z1000SX 2011-2016 For Kawasaki ZX-6R 636 2006 For Kawasaki ZX10R2009 For Kawasaki ZRX1200 2011-2015 For Kawasaki Brute Force 750(ATV) all years For Kawasaki Mule (ATV) all years For Kawasaki Teryx (ATV) all years With description: Condition: 100% Brand New Light Source Color: Red/Blue/Green/White/Orange Item Name: Transmission Gear Display Indicator Size: 4cm*4cm*4cm/1.57in*1 .57 inch * 1.57 inch * 1.57 inch Function: Shows the current gear number. Indicates the current gear from 1st to max 6th, and also has a neutral indicator. Detects the current gear faster than other gear indicators that use the speedometer/tachometer signal. Display can be mounted anywhere Preface: Congratulations on purchasing the Gear Position Indicator, this product will fit all Fuel Injected (EFI) Kawasaki motorcycles that have an on-board diagnostic system connector. This connector is referred to as for KDS (Kawasaki Diagnostic System) in Kawasaki manuals. Unlike other gear indicators available for your bike, this product connects to a diagnostic connector. This makes installation very easy. The unit reads data directly from the ECU, offering faster and more reliable readings than competing products. Display is auto-learning, no button and no "programming wire" limitation; Your bicycle is not equipped with a gear position sensor. Therefore, it is only possible to determine the transmission used when the engine is running and the clutch is released. Orze installation: 1. Locate the 4-pole diagnostic connector (called r oacute; also for KDS) under the seat, near the ECU module (black, gray or p oacute; translucent plug). 2. It usually has a removable poacute;l-transparent cap or? A pacifier? Plug (without wires) attached to it. The connector may be partially covered with black tape. Note: You may find two of this connector on the bike. In this case, try both connectors, but only one of them will provide data for this display. If you connect the oacute;w to the wrong plug, it will not harm your bike. 3. Disconnect the cover (cap) from the plug and connect the plug to display the oacute;w. 4. Reroute the cable to the mounting location along the frame. Remove the green plastic from the back of the device and install the display. 5. Secure the cable with the supplied cable tie, ensuring that the cable does not obstruct the movement of the steering wheel. Ciu problem solving: You can find two transparent connectors on the bike with a removable cap or a dummy plug. Try a second one if the unit doesn't work from the first one. Unplug the connector, display the oacute; and check if the pins are broken, bent or pushed out of position. Reconnect the plug, and make sure all connections are good and the connector is fully seated. If you are unable to complete the setup procedure, your battery may be old or weak. Charge the battery or connect another battery using the jumper cable. If some gears are not indicated correctly when the engine is running and the clutch is released, disconnect the unit and readjust. If the problem persists. Your clutch may be slipping. Su package list oacute;w: 1 x Display/Bracket Motorcycle Gear Box(As option picture shown)