Special Note: Carefully review the product photos corresponding to the options you ordered and the products described in each option before purchasing. Thanks Features: Condition: 100% Brand New Light Color: Red Waterproof Level 1-6 Gear Display Equipment: For Suzuki GSF600 Bandit 2000-2004 For Suzuki GSF650 Bandit 2005-2006 For Suzuki GSF1200 Bandit 2001-2006 For Suzuki XF650 1997 -2004 for Suzuki VL800 intruder Volusia 2001-2004 For Suzuki SV650 1999-2002 For Suzuki GSX1300R Hayabusa 1999-2007 For Suzuki GSX750F Katana 1998-2006 For Suzuki GSX600F Katana 1998-2006 For Suzuki GSX-R750 1996-2004 (Does not fit 200 0) For GSX-R600 Suzuki 1997-2000 K1 K2 K3 For Suzuki DL650 Vstrom 2012-2019 For Suzuki DL650XT Vstrom 1999-2002 For Suzuki TL1000 R/S 1998-2003 For Suzuki VL1500 intruder 2013-2017 For Suzuki VZR1800 2011-2019 For Suzuki intruder c1500 2013-201 7For Suzuki Boulevard c90 2013-2019 For Suzuki GSX250R 2018-2019 For Suzuki GSX1000F Katana 2019 For Suzuki GSX1400 2001-2009 For Suzuki GSXR1000 2001-2016 For Suzuki GSXS750 2015-2019 For Suzuki GSXS750Z 2018-2019 For Suzuki GSXS1000 /F/A/FA 2015-2019 For Suzuki GSXS1000Z 2 018-2019Locate the speed sensor connector:The speed sensor is usually mounted on front sprocket cover, and the 3-pole black speed sensor connector (as shown in the picture) is located 20-40 cm (8"-16") away from the sensor. The connector is accessible by lifting the fuel tank, removing the seat or side fairing ( as shown in the picture).Confirmation:1. Separate the speed sensor connector (you may need to use a small flat-head screwdriver to separate the connector).2. After separating the speed sensor connector, connect both the male and female 3-pole GFYSHIP harness connectors. Make sure the connectors are fully seated.3. Locate the wire coming from the signal generator (pick up coil/CKP sensor). If in doubt, check your bike's service manual or ask your dealer.4. Connect the green wire to this wire using the provided red wire tap connector (the green wire is connected to the crankshaft sensor signal line) Configuration: You need to configure the module after installation. When the ignition is turned on, it will display backwards (6 to 1), which means the memory is clear. - Lift the rear wheel off the ground with a stand and start the engine in neutral. (If you don't have a center stand, you can find a long and straight road with little traffic.) -When the runway display screen shows "L", it means learning has started; Accelerate slowly through the throttle grip - When the gear display displays "1", please select first gear, the display will flash faster while the unit learns the gear, release the clutch and keep the rpm above idle speed; - When the gear display displays "2", please select two-position ;-Repeat this process until all gears have been thought of (5 or 6).-The unit is programmed and should indicate the gears correctly.-Now when the ignition is turned on, it will display forward (1 to 6) indicating that it is fully functional .Steps to reset the product:Turn on the switch lock key switch. When the gear display shows 3, immediately turn off the switch lock key switch, and then immediately turn on the switch lock key switch. According to the above operation, turn the switch lock key switch on and off six times in a row to check whether the reset is completed (after turning on the ignition, it will display backwards (6 to 1) indicates that the memory has been cleared). Thank you