Eye Moisturizing Spray Machine Hot Cold Compress Dry Eye Relief Wrinkle Removal Eye Sprayer Item Type: Eye Spray Machine Material: ABS, silicone, PC Battery Type: Lithium battery Battery Capacity: 800mAh (built in) Power Supply Method: USB charging When Adding Water to the Instrument: ① Use your fingers to hold down the back cover on both sides of the non slip pattern to pull back to open ② Counterclockwise unscrew the water cup cover ③ Liquid into the water cup ④Tighten the water cup cover clockwise Working Modes: Mode One: Spray (hydration, cold compress) Press the button to turn on, the indicator light is green, the instrument enters the working mode a micron atomization spray working state (Note: the atomization piece of the instrument needs to contact the water to normal atomization spray, please ensure that the direction of the atomization port is facing down or downward tilt state, the instrument water cup is designed with 1ML water storage tank, this design is to prevent the instrument spray port in the upward state can also maintain a short period of normal spray.) Mode Two: Vibration massage, hot compress, hydration, cleaning button press the second button after power on, the light is blue, the instrument enters the work mode two, into the micron atomization, vibration warm massage work state, (at this time micron atomization spray work 3 seconds after stopping 3 seconds, micron atomization spray cycle) instrument warming warming time takes about 15 seconds, the instrument in different temperature environment will also lead to warming the required (time is different) Mode three: vibration massage, hot compress button after the button is pressed for the third time, the indicator light is purple red, the instrument enters the work mode 3, at this time the instrument vibration massage, hot compress function to start, hot compress temperature 40 ℃ ‑45 ℃, the time required for warming up and mode two, the instrument 3 working modes in turn cycle, long press the button for 3 seconds to shut down, the indicator light is off. Charging: 1. Instrument built in lithium battery power supply, it is recommended that the user is fully charged before the first use! 2. Instrument in the power on state when the red light flashes, battery power is low, (the instrument automatically shut down 3 minutes after the light flashes), please charge in time. 3. Instrument charging state indicator light is red, charging completed indicator light is green. 4. The instrument control circuit adopts intelligent charging system, charging 30 minutes to about 60% of the power, fully charged about 90 minutes. When the instrument is on during charging, the circuit system will close the charging channel and stop charging. 5. Eye nourishing and slow pressure instrument fully charged working hours: Mode one working time: about 180 minutes Mode two working time: about 80 minutes Mode three working time: about 90 minutes. Instrument Maintenance Recommended Methods: 1. Before and after the use of the instrument, wipe with a clean tissue or dust free cloth with water repeatedly more than 3 times, the machine is completely dry and then put away. 2. When not in use for a long time, you need to pour out the remaining liquid in the water cup and shake out the water cup, and wash the water cup with pure water more than 2 times when the instrument is used for the first time and used again. Note: 1. In the water cup lid screwed into the water cup need to let the water cup lid snap aligned with the water cup groove slightly down and then tighten clockwise can be, in case of water leakage at the water cup lid, please check whether the waterproof ring in the water cup lid put flat. 2. Instrument in the state of power on mode 1 and mode 2, the water cup is green light, you can observe the water level in the cup through the transparent water level window on the back cover, and add water at the right time. ③Instrument does not have waterproof, not washable, when filling water to avoid the amount of water beyond the water cup, please cover the waterproof spigot cover, to avoid the charging port water; after filling water, please tighten the lid to avoid seepage of water, resulting in machine dysfunction. ④Do not add impurities and grease containing liquid, impurities and grease will cause clogging of the atomizer and can not be sprayed! (It is recommended e physiological saline or eye wash to moisten the eyes and relieve the dryness.) ⑤ hot compress before please remove the contact lens, hot compress must be closed, so as not to burn the cornea, the eyelid is the image of the hot compress. ⑥For the protection of the machine, the apparatus will be shut down after 10 minutes of work without operation. ⑦The instrument should avoid contact with acid and harmful substances.