1m/2m/5m Portable PCB Photosensitive Dry Film Fit for Circuit Production Photoresist Sheet

¥3,449
配送料無料

1m/2m/5m Portable PCB Photosensitive Dry Film Fit for Circuit Production Photoresist Sheet

  • ブランド: Unbranded

1m/2m/5m Portable PCB Photosensitive Dry Film Fit for Circuit Production Photoresist Sheet

  • ブランド: Unbranded
価格: ¥3,449
販売元:
¥3,449
配送料無料

在庫あり

以下の支払い方法を利用することができます

説明

["Feature:\n1.5 mil thickness of dry film can be completely cover a hole of 0.25 inches\nThe dry film can be used in the most ordinary plating solution, no wrinkle, no discoloration\n\nOperating steps:\n1, grinding CCL, this simple, using the finest polished clean water frosted paper on the line\n2, removing film, photographic film is sandwiched between two layers of film, the first side can make use of transparent tape tear torn, try a few on the line\n3, and then foil, copper clad laminates can look a little cleaner, pasted, try not to have bubbles.\n4, good paste membrane used presses, not too hot, about 100 degrees from the fixing.\n5, the printed circuit board film, suggestion is to use film, the fine could reach the highest degree of accuracy if you did not ask for the paper to print it with sulfuric acid trip.\n6, the printed circuit on the photographic plate (Note: Dry film is negative, so to highlight the print, which we usually use photographic plate opposite) with ordinary energy-saving lamps 10 or so, if there is exposure Machine 1 minutes on the line, the for sun not tried, it should be 30 seconds -60 seconds, the exposure process Obviously, since the photosensitive film will change color when exposed to light, the light becomes dark blue. You will easily see your circuit diagram appeared on the board.\n7, developing and tear the protective film on the front panel, into the developer (developer according 1:100,10 gram Total 1L of water) to be used when developing a little harder stick cotton wipe board.\n8, etching, this goes without saying (ferric chloride etchant environmental For protection, hydrochloric acid + hydrogen peroxide, etc.) is recommended environmental etching shop, fast, clean, no odor.\n9, after a good CCL etching, stripping, from film watered by 1:60 or 70, the board bubble like a few minutes\n10, after the completion of the board, very pretty good, most dense line spacing is 0.1mm, width 0.1mm, 0.1mm lines do know though is very easy to do, but do 0.1 lines and 0.1 line spacing dry film can easily do it\n\nSpecifications:\nMaterial: Organic Resin\nWidth: 30cm\nLength: 1m/2m/5m\nQuantity: 1 Roll\n\nNote:\n1.Transition: 1cm=10mm=0.39inch\n2.Please allow 0-3cm error due to manual measurement. pls make sure you do not mind before you bid.\n3.Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!\n\nPackage includes:\n1 Roll x Photosensitive Dry Film"]
  • Fruugo ID: 386131956-829785703
  • EAN: 7934001094634

配送と返品

24時間以内に発送

  • STANDARD: 無料 - 間の配達 月 03 11月 2025–木 06 11月 2025 - 無料

中国より発送。

ご注文の商品は、お客様の仕様に従い、万全の状態で配送されるように最善を尽くしています。しかし、もし注文に抜けがあったり、注文したものと違う商品が届いたり、注文に満足できないその他の理由がある場合は、注文全体やその中のいずれかの商品を返品し、その全額の返金を受けることができます。 全額返金ポリシーを見る

製品コンプライアンスの詳細

以下に概説されているこの製品に固有のコンプライアンス情報を参照してください。

以下の情報は、この製品を販売する独立したサードパーティ小売業者によって提供されています。

製造業者:
次の情報は、Fruugoで販売される関連製品の製造業者の連絡先詳細です。

  • Shenzhen Yiyuxun Hardware Tools Co., Ltd.
  • Shenzhen Yiyuxun Hardware Tools Co., Ltd.
  • Room 205, Building D10, No. 5, Cengyao Industrial Zone, Yulv Community
  • Yutang Street, Guangming District
  • Shenzhen
  • China
  • 518000
  • mingtanghi@163.com

EUにおける責任者:
次の情報は、EUにおける責任者の連絡先情報の概要です。ここで言う責任者とはEUに拠点を置く指定経済事業者で、EU域内で販売される関連製品に関するコンプライアンス義務を負う者のことです。

  • Yating He
  • E-CrossStu GmbH
  • 69 Mainzer Landstrasse
  • Frankfurt am Main
  • Germany
  • 60329
  • E-crossstu@web.de
  • +4969332967674