Feature 1The auger ground digger is made of highquality plastic + manganese steel material, durable, wear resistant, corrosion resistant, can be used for a long time. 2Large capacity fuel tank, simple switch operation, support one handed operation, with a comfortable shockproof handle for easy control. 3The 2 stroke ground digging machine has a built in translucent fuel tank that allows you to easily track the correct fuel level. 4Equipped with easy to start pull rope, quickly connect to pull the starter, one key throttle switch design, quick and convenient start. 5Can effectively improve the efficiency of digging holes, can work on any type of soil, greatly improve planting efficiency.Item Type: Hole DiggerMaterial: Plastic + Manganese SteelWeight: Approx. 9350g / 329.8ozProduct Size: Approx. 55x35.5x29cm / 21.7x14.0x11.4inGround Drilling Power: 48FPower Displacement: 63CCApplicable Drill Diameter: 20mm / 0.8in, 100x800mm / 3.9x31.5in SpecificationPower: 2.3kwMachine Fuel: A mixture of gasoline and engine oil (Not Included)Fuel Use:1. The gasoline is 92# and above unleaded gasoline, and the engine oil is a special 2 stroke engine oil or a special 2 stroke FC grade engine oil for Mobil, for Changcheng, and Tongyi.2. Within 20 hours of use of the new engine, gasoline: engine oil = 25:1 (JASO-FC grade); after 20 hours of use, it is recommended to use special 2 stroke engine oil, and the fuel mixture ratio at this time is 50:1.(Note: 1. The oil must be changed after the new machine is used for 2 hours, and the oil must be changed every 8 hours thereafter. 2. The oil should be changed under the warm state of the engine to facilitate the rapid and thorough discharge of the oil)Scope of Application: Planting hole drilling, fence pillar drilling, greenhouse pillar drilling, optical cable road pillar drilling, boundary marking drilling, pile fertilization drilling, winter ice fishing drilling, tree transplanting planting drillingInstallation Steps:1. Place the gasoline engine and the drill bit on the ground, so that the output shaft and the drill bit are basically at the same horizontal position2. Install the drill bit on the output shaft and align it with the pin shaft installation hole3. Pass the pin shaft through the mounting hole on one side of the drill, the mounting hole on the output shaft, and the mounting hole on the other side of the drill.4. Pass the cotter pin through the pin hole, and bend the opening of the cotter pin slightly to both sides (the drill bit is not included)Start Method of Digger:1. Fill the oil pot with a proper amount of mixed fuel, and tighten the lid of the oil pot to make it completely leakproof.2. Press the flameout switch in the opposite direction of "OFF" to make it in the on state; Note: "NO" is a stop sign.3. Continuously lightly press the carburetor oil bubble by hand until there is fuel in the oil return pipe (transparent oil pipe) returning to the oil tank.4. Move the choke door to the fully closed position as indicated by the label.5. Use one hand to hold the gasoline engine at a proper position, and the other hand to hold the start handle, quickly and continuously pull the start rope 3-5 times diagonally. If it can be started, the start rope is automatically and slowly returned to In situ; if it cannot be started, move the choke back to 1/2 opening or fully open according to the label instructions, and then quickly and continuously pull the start rope 3-5 times diagonally to start. (Easy starter device: Quickly and continuously pull up the starter handle diagonally to start. When returning, hold the starter handle tightly and let the starter rope automatically return to the original position at an even speed. Don't let go suddenly to prevent the starter handle from returning quickly rebound, causing damage to the starter assembly.) .wang-edit-text{ font-family:'Arial' !important; } .wang-edit-text table { border-top: 1px solid #000; border-left: 1px solid #000; } .wang-edit-text table td, .wang-edit-text table th { border-bottom: 1px solid #000; border-right: 1px solid #000; padding: 3px 5px; } .wang-edit-text table th { text-align: center; }Package List1 x Ground Digger Host1 x Accessory Kit (2 x Hex Wrench, 1 x Wrench, 1 x Screwdriver Bit, 1 x Screwdriver Handle, 1 x Socket Wrench)1 x English Manual1 x Oil PotNote1. Please allow 01 inch error due to manual measurement. Thanks for your understanding.2. Monitors are not calibrated same, item color displayed in photos may be showing slightly different from the real object. Please take the real one as standard.3. Customers can use it with a drill bit by th