1、Compliant with Serial SATA 0 specification, backward compatible with SATA0 SATA0. 2、Compliant with PCI-Express v0 specification and backward compatible with PCI-Express v0. 3、Support Gen 1i, Gen 1x, Gen 2i, Gen 2m, Gen 2x, and Gen 3i. 4、Support FIS based on port multiplier switch or command switching. 5、Compatible with SATA6G, 3G and 5G hard drives. Features: Compliant with Serial SATA 3.0 specification, backward compatible with SATA 2.0 SATA 1. 0. Compliant with PCI-Express v 2.0 specification and backward compatible with PCI-Express v 1. 0. Support Gen 1i, Gen 1x, Gen 2i, Gen 2m, Gen 2x, and Gen 3i. Supports communication speeds of 6.0 Gbps, 3.0 Gbps and 1.5 Gbps. Support FIS based on port multiplier switch or command switching. Compatible with SATA6G, 3G and 1.5G hard drives. Support AHCI 1.0 mode and IDE mode. Support for native command queue (NCQ). Support hot swap. Support 4 SATA.   Specification: Name: 6-port SATA 3.0 expansion card Model: PCE6SAT-M01 Master control: for marvell 88SE92xx+109X Interface: PCI-E 1x, 2x, 4x, 8x, 16x Support system: for WINXP / WIN7 / WIN8 / WIN10 / LINUX Bus interface: PCI-Express x1 slot Expansion interface: 6 SATA 3.0 interfaces Product size: approx. 12 * 10 * 2cm / 4.7 * 3.9 * 0.8inch   The PCIE to SATA 3.0 riser card is used as follows: First, the system disk and PCIE to SATA 3.0 riser card connection conditions and solutions: 1. The SATA interface mode of PCIE to SATA 3.0 is AHCI mode. If you want to plug in the system disk on our card, the premise is that your system disk must be installed in AHCI mode when installing the system on the motherboard. Otherwise, the system cannot be started through our transfer card. 2. If it is determined that the SATA interface installation system of the system disk inserted in the motherboard is AHCI mode, then you can directly insert the hard disk into our card, and then enter the motherboard BIOS to set the system disk as the first boot. 3. If the above two conditions are met, if the hard disk interface of the motherboard still fails to start, or restarts repeatedly, it may be caused by the conflict between the hard disk interface of the motherboard and our transfer card. The solution is to enter the motherboard BIOS and set the hard disk interface option of the motherboard to Disabled, then save and restart to start the system.   Second, the common disk and PCIE to SATA 3.0 connection conditions and solutions: 1. When the system disk is inserted on the motherboard, the ordinary disk is inserted in the PCIE to SATA 3.0 card, then only the adapter card information and the normal disk model need to be detected at startup. 2. If the condition is established, or can not start the system, then you must enter the motherboard BIOS, set the system disk to the first boot.   Third, the system disk and the ordinary disk and PCIE to SATA 3.0 connection and solution: 1. Premise, if the system disk with the original motherboard installed system is AHCI mode test, can use the following methods to achieve, if it is IDE mode installed system, then you can only reinstall the system through PCIE to SATA 3.0 . 2. When the first condition is established, and you still can not start to enter the motherboard BIOS, set the system disk to the first boot. 3. When the first and second conditions are met, and you still can not start, then it may be integrated SATA interface conflict, please enter the motherboard BIOS to set SATA to Disabled.   Package List: Riser card *1 Half height baffle *1