Features： 1、One‑piece molding to prevent rain and dust from entering the internal corrosion parts, longer service life and safer. 2、Built‑in intelligent temperature control chip, 40°C/50°C/60°C three‑level adjustable temperature. 3、12V voltage, 22mm(7/8in) handlebar inner diameter, suitable for most motorcycles, wide application. 4、With double throttle cable buckle, wider installation range, which is more practical to use. 5、Added standby mode. After switching to the standby state, the heating handle will automatically keep the temperature to about 50°C, and it will automatically shut down after 2 hours. There is no need to worry about running out of battery power because of forgetting to turn off the switch. Specification： Condition: 100% Brand New Item Type: Motorcycle Heating Handle Material: Butyronitrile Color: As picture shown Model: ZH-983C1 Voltage: DC12V Power: Red Light 35W, Blue Light 25W, Green Light 17W Left Handlebar Size: Approx.143 x 36mm/5.6 x 1.4in Right Handlebar Size: Approx.127 x 36mm/5 x 1.4in Suitable Pipe Diameter: Approx. 22mm/0.9in Handle Temperature: Low temperature: 40°C, medium temperature: 50°C, high temperature: 60°C Switch Type: Aluminum alloy multi-speed adjustable temperature control switch Instructions: 1. Power On: Red light, blue light and green light each flash once and then go out 2. Standby: The red light is in the state of breathing and flashing, and the temperature reaches the highest temperature and it will automatically become the blue light mid-range, and it will automatically shut down after 2 hours 3. Working Status: Indicator light is always on (high-end: red light is always on, mid-range: blue light is always on, low-end, green light is always on) 4. Long press the power button for 3 seconds: enter the standby state or shut down 5. Click on the Key: Switch gears How to Use the Switch: Long press for 3 seconds to turn on, the red breathing light will turn on automatically when it reaches a certain temperature, it will automatically turn blue, lightly press to change to blue light, the temperature is medium temperature, lightly press twice to change to green, the temperature is the lowest, press three times for Red three-speed high temperature, long press for 3 seconds to turn off, standby for 2 hours to automatically turn off, no longer have to worry about wasted power Installation Notes: 1. First remove the original handlebar with tools, then clean the handlebar 2. Then moisten the inner holes of the left and right handles of the product with soapy water, respectively, install the left and right handles on the handlebars, and the twisting amplitude should not be too large during installation. 3. When installing the right handlebar, the power cord should be left enough for rotation to facilitate the rotation of the accelerator 4. Then fix the S bracket on the handle of this product to the position where the handle has screws, and then fix the wire on the bracket to avoid the handle wire from shaking back and forth and reduce damage 5. The red wire of the product power cord is connected to the positive pole of the power supply of the car, and the black wire of the product is connected to the negative pole of the power supply of the car. 6. Because this product switch has two fixing methods (rearview mirror fixing, tape fixing), you can fix the aluminum alloy switch to the L bracket with small screws, and then fix the L bracket to the rearview mirror base and tighten; or Directly use tape to stick to the back of the aluminum alloy switch, and then stick the adhesive tape to a suitable position on the car to fix it. Wiring Method: 1. Connect to the circuit of the motorcycle electric lock (behind the key), the red line is connected to the positive pole output line of the electric lock, and the black line is connected to any negative pole on the car (this method is suitable for those who do not want to use standby state but forget to turn off the switch easily). . 2. Connect the positive and negative positions of the battery, connect the red to the positive and negative of the battery, and the black wire to the negative of the battery. Because this electric handle adds a standby automatic shutdown function, even if you forget to turn off the switch when the battery is connected, just turn it on to standby mode, no need to worry about running out of battery. Package List： 1 x Electric Heating Handlebar Kit 1 x L‑Shaped Bracket 1 x Sticker