9 in 1 RF Vacuum Cavitation Machine High Frequency Skin Firming Prevent Aging Fat Burning Machine 100‑240V AU Plug Item Type: Vacuum Cavitation Machine Material: ABS Operation Method: I. Color Meridian Brush: Method: After using the serum, use the probe to massage the specific part of the treated skin in a circle to adjust the output energy and mode of a total of M1, M2, M3, M4 four modes, as described below: "M1" continuous work, "M2" continuous work for 2 M2" works continuously for 2 seconds, with a pause of 2 seconds. "M3" continuous work for 1 second, pause for 1 second. "M4" continuous work 0.5 seconds, pause 0.5 seconds. The handle can be adjusted to 7 photon modes. First, turn on the switch on the machine screen, make sure the power supply is greater than 0, press "-" "+" to adjust the LED color. 1.Red:Activate suitable for any skin, promote blood circulation, regenerate collagen, make skin smooth, treat dry skin disorder, hair removal, degeneration and follicular disease. 2. Green: Balance normal sebaceous glands, reduce blackheads and sores, and balance moisture. 3. Blue: Calming for sensitive, oily and pimple skin, reduce and eliminate pimple bacteria, get rid of pimples, promote collagen and protein complex, revitalize skin, tighten loose skin and pregnancy wrinkles. 4. Purple: Drain water, renew skin, reduce wrinkles. 5. Orange: brighten and decompose pigments, smooth the skin. 6. Cyan: defense to enhance the ability to protect the skin, calming, release stress. 7. White: guide the skin to absorb nutrients, anti aging. 8. Circulation 2. 40KHz cavitation head: a collection of strong sound waves head, can be launched to the body 40KHZ strong sound waves, violent impact on fat cells, causing frictional movement between fat cells. This may cause the heat and water in the fat cells to be effectively consumed, making the fat cells smaller. Moreover, the acoustic wave vibration may cause a violent shock to explode the fat cells instantly, reducing the number of fat cells and thus achieving the effect of fat removal. M1, M2, M3, M4 four modes, respectively: "M1" continuous work for 3 seconds, not continuous work for 3 seconds. "M2" continuous work for 2 seconds, intermittent work for 2 seconds. "M3" continuous work for 1 second, intermittent work I seconds. "M4" works continuously for 0.5 seconds and intermittently for 0.5 seconds. Operate with 40KHz cavitation head for 15-20 minutes, mainly spiral movement on the body. Press "-" "+" to adjust the operation duration. Touch to adjust the cavitation mode in M1,M2,M3,M4 mode. Touch "-" to decrease the strength, touch "+" to increase the strength. Press the "Start" button to start the strong sonic burst fat head. Method: After applying the slimming cream for about 15 ~ 20 minutes, use the probe to massage in a circular motion on the specific part of the skin being treated. Can accelerate the blood flow of the skin in the treatment area, with the effect of decomposition of fat. Caution:1. Apply slimming cream or cooling gel to the skin area to be treated before treatment.2. Keep the probe in close contact with the skin.3. Adjust the strength from low level to high gear.4. Do not put the applicator in the same place.5. Move the applicator slowly but constantly.6. Avoid treating bones and do not target joints directly.7. Pay attention to the temperature of the cavitation handle when using Stop using for ten minutes after half an hour of use. 8. Cavitation is strictly forbidden without glue operation. 3. 4 Pole Radio Frequency Head： Press the "FACE RF" on the display to select the surface RF output, set the RF mode: touch can be adjusted in automatic, M1, M2, M3 mode RF mode. Automatic mode always output, M1 output 0.5 seconds, M2 output 1 second, M3 output 1.5 seconds, select the appropriate strength (according to customer acceptable level adjustment, recommended 20%-60%), press "START" key to start operation. Operation with facial RF head massage 15-20 minutes, with facial spiral movement mainly around the eyes. Note: 1. apply gel or serum evenly on the treatment area. 2. keep the probe in close contact with the skin. 3. adjust the strength from low to high level. 4. do not put the applicator in the same place. 5. move the applicator slowly, but constantly. 6. the skin around the eyes and forehead is very sensitive, the RF output strength should be kept at a relatively low level. 7. if you need to rest during the treatment, please "pause" first and then press "START" to start the operation. 8. Please first "pause" and then "stop" to avoid excessive output of the machine. 4. Tripolar Radio Frequency Head: Press the "eye RF handle" on the display to select the RF output, set the RF mode: touch can be adjusted between Auto, M1, M2, M3 mode RF mode, Auto mode always output, M1 output 0.5 seconds, M2 output 1 second, M3 output 1.5 seconds, the gel evenly coated in the treatment area. Select the appropriate strength (can be adjusted according to customer