Replacement Spray Nozzle PrintHead Office Printer Repair For C-anon I560 IP3000 I850 MP700 MP730 QY6-0042 Printers Multi-Color

¥9,490
配送料無料

Replacement Spray Nozzle PrintHead Office Printer Repair For C-anon I560 IP3000 I850 MP700 MP730 QY6-0042 Printers Multi-Color

  • ブランド: Unbranded

Replacement Spray Nozzle PrintHead Office Printer Repair For C-anon I560 IP3000 I850 MP700 MP730 QY6-0042 Printers Multi-Color

  • ブランド: Unbranded
価格: ¥9,490
販売元:
¥9,490
配送料無料

在庫あり

以下の支払い方法を利用することができます

説明

["Description:\nIt is of high quality.\nFeature:\nHigh quality TESTED IN GOOD WORKING SITUATION AND REFURBISHED\nMade of high-quality materials, durable and perfectly matched with the original version\nOther features: stable characteristics, high reliability, according to the original factory specifications. Easy and simple installation\nApplicable model: for C-anon I560 IP3000 I850 MP700 MP730 QY6-0042 Printers\nUse scene: printer nozzle\nPrinter for Head only, other accessories demo in the picture is not included!\n\nSpecifications:\nItem Type: Printer for Head\nMaterial: ABS\nColor: As shown\nModel: QY6-0042\nSize: (approx) 18x10x5cm\nPrinting color: Full Color/Black(optional)\nQuantity: 1 Pc\n\nPrecautions:\n1. The for head surface of the nozzle is very fragile and must not be bumped. It must be protected. Its surface layer is an aluminum sheet, and the inner layer is coated with a crystal oscillator and a very small ink tube. It will be concave and deformed when touched. Even if it breaks, the nozzle will be scrapped;\n2.Before installation, please make sure that the other parts of the printer are normal, especially the motherboard to ensure that they are normal, otherwise the new print for head may be burned out.\n3. When connecting the plug and cable, do not bring ink, and make sure that it is in good contact with the socket and does not for touch the feet, otherwise, it will cause the nozzle to be short-circuited and burned;\n4. The steel shaft should also be clean and smooth. You can wipe it with a paper towel with some lubricating oil. Do not directly add oil to the shaft. The excess oil will flow to the nozzle and cause damage;\n5. After the machinery and circuit are all correct, check the water circuit. First, check that the amount of water in the ink cartridge is insufficient; second, check whether the small cleaning blade and the ink suction pump are dirty;\n6. There may be air in the newly installed print for head, so it will not print normally immediately. Only when the air in the for head is completely exhausted can the line be normal; first, intermittent cleaning can be used (only two cleanings at a for time, then stop 30 Wash 2 times after 2 minutes) Repeatedly over-cleaning will cause ink accumulation in the cleaning pump, which will not only cause color mixing and ink leakage, but also waste ink; secondly, you can print more pictures to let the nozzle discharge air during work ; Again, if the machine has led out the waste ink tube, you can cut off the power first, and then use a rubber tube to draw out the waste ink tube until 3-5ml of ink is drawn out, then turn it on and clean it once with the machine normally. It is equivalent to artificially extracting the air from the for head, and the side effect is that it is easy to cause the cleaning pump to pile up ink.\n7. The status of this product is REFURBISHED IN WORKING SITUATION. If it is marked as brand new, it will be on the shelf or for publicity. This description shall prevail, thank you\n8. Please let professionals install or operate, damage caused by human causes, NO refund.\n\nNote:\nTransition: 1cm=10mm=0.39inch\nPlease allow 0-3cm error due to manual measurement. pls make sure you do not mind before you bid.\nDue to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!\n\nPackage Includes:\n1 x Printer for Head"]
  • Fruugo ID: 386091413-829715223
  • EAN: 7934017639997

配送と返品

24時間以内に発送

  • STANDARD: 無料 - 間の配達 木 30 10月 2025–火 04 11月 2025 - 無料

中国より発送。

ご注文の商品は、お客様の仕様に従い、万全の状態で配送されるように最善を尽くしています。しかし、もし注文に抜けがあったり、注文したものと違う商品が届いたり、注文に満足できないその他の理由がある場合は、注文全体やその中のいずれかの商品を返品し、その全額の返金を受けることができます。 全額返金ポリシーを見る

製品コンプライアンスの詳細

以下に概説されているこの製品に固有のコンプライアンス情報を参照してください。

以下の情報は、この製品を販売する独立したサードパーティ小売業者によって提供されています。

製造業者:
次の情報は、Fruugoで販売される関連製品の製造業者の連絡先詳細です。

  • Shenzhen Yiyuxun Hardware Tools Co., Ltd.
  • Shenzhen Yiyuxun Hardware Tools Co., Ltd.
  • Room 205, Building D10, No. 5, Cengyao Industrial Zone, Yulv Community
  • Yutang Street, Guangming District
  • Shenzhen
  • China
  • 518000
  • mingtanghi@163.com

EUにおける責任者:
次の情報は、EUにおける責任者の連絡先情報の概要です。ここで言う責任者とはEUに拠点を置く指定経済事業者で、EU域内で販売される関連製品に関するコンプライアンス義務を負う者のことです。

  • Yating He
  • E-CrossStu GmbH
  • 69 Mainzer Landstrasse
  • Frankfurt am Main
  • Germany
  • 60329
  • E-crossstu@web.de
  • +4969332967674