DCDC 532V to 1V30V Automatic Step up Down Converter Boost Buck CC CV Power Supply Module

¥3,399
配送料無料

DCDC 532V to 1V30V Automatic Step up Down Converter Boost Buck CC CV Power Supply Module

  • ブランド: Unbranded

DCDC 532V to 1V30V Automatic Step up Down Converter Boost Buck CC CV Power Supply Module

  • ブランド: Unbranded
希望小売価格: ¥4,399
価格: ¥3,399
得する金額: ¥1,000 (22%)
販売元:
¥3,399
配送料無料

在庫あり

以下の支払い方法を利用することができます

説明

This power supply is a high efficiency regulated power supply module. Output voltage can keep stable when input voltage is below, above or equal to the output voltage.For example, if the output voltage is set as 12V, then even the input voltage changes from 5V to 32V, the output voltage will still be 12V.This module has well protection function, which can be applied to solar battery charging.This power supply is an automatic step up/down power supply module. Output voltage can keep stable when input voltage is below, above or equal to the output voltage.For example setting the output as 12V, the input voltage changes within 5 ~ 32V output voltage is always 12V;It has constant voltage, constant voltage, under voltage protection,and output indication, fault indicator function, output over current, over voltage, short circuit protection;all components can achieve industrial applications.Can be perfectly used in various occasions,such as charging, high power LED driver, device power supply, car power source, etc.Features:The circuit board is thickly plated .The fuse of input can be changed, to protect power supply and equipment.Using high quality chips, low resistance and high frequency capacitor.The module uses imported original IC.It has constant voltage, constant voltage, and under voltage protection.Oxidized heat sink is better at cooling than original color aluminum heat sink.The material of inductor is sendust, it can heat less.Specification:Type: Non-isolated step up/down moduleInput Voltage: DC 5V-32V(suggest 10V above )Output Voltage: DC 1V-30V(continuously adjustable)Output Current: 10A(max),less than 7A for long-term useOutput Power: 80W(suggested), 130W(max). Please enhance heat dissipation when power is more than 80W.Output Ripple: 50mV (measured at 5A, 12V to 12V)Reverse Input Protection: Not support. If needed, a schottky diode can be added in series at input.Output Flow Back Protection: Not support. If used for storage battery charging or powered inductive load, a schottky diode can be added in series at output.Short Circuit Protection: YesWeight: 45g / 1.6oz (approx.)Adjustment Method:1. Battery under voltage protection adjustment method:(take 12V lead-acid battery as an example, set 10V under-voltage protection, shut off output)Input is connected to regulated power supply adjusted to 10V, adjust under-voltage protection potentiometer (clockwise to increase, counterclockwise to reduce), till the failure indicator (red) light is on. Then when the battery discharge to 10V, it will automatically cut off power supply to protect battery from damage.Note:If not powered by batteries, you can skip this setting.2. Output voltage adjustment methods:Input is connected to power source (voltage is higher than the under-voltage protection value), the red light is off while blue light is on. Output is connected to multimeter, adjust output voltage potentiometer (clockwise to increase, counterclockwise to reduce) till the required voltage;Note: Normally the red light is off, blue light is on, otherwise there is fault, input under-voltage protection, output over-current protection, output short circuit protection, please troubleshoot and power on again.2. Output current adjustment methods:(take 12V input to charge 12V lead-acid battery as example, the charging current is 5 A)Input is connected to 12V power supply, turn multimeter to current position, output is connected to multimeter in parallel (red pen to output positive, black pen to negative, short circuit output directly.It is suggested to use current positions more than 15A, in case of burning out fuse), adjust constant current potentiometer (clockwise to increase, counterclockwise to reduce), till it displays required current 5A, then remove the multimeter,connect to the battery to charge normally. If use ammeter to adjust output current, refer to current meter corresponding circuit correctly connect and debug.Note: If used for constant voltage equipment, only need to set the maximum output current.Note:Please note that the new type and old type of this product will be sent randomly and make sure you will not mind before ordering..
  • Fruugo ID: 416437485-878746339
  • EAN: 7540131209734

製品安全情報

以下に概説するこの製品に固有の製品安全性情報を参照してください。

以下の情報は、この製品を販売する独立したサードパーティ小売業者によって提供されています。

製品安全ラベル

CE Mark
安全上の警告: Warning: Please read the product instructions carefully before use to ensure correct use.
シリアルナンバー: 7540131209734

配送と返品

2日間以内に発送

  • STANDARD: 無料 - 間の配達 月 27 10月 2025–月 03 11月 2025 - 無料

中国より発送。

ご注文の商品は、お客様の仕様に従い、万全の状態で配送されるように最善を尽くしています。しかし、もし注文に抜けがあったり、注文したものと違う商品が届いたり、注文に満足できないその他の理由がある場合は、注文全体やその中のいずれかの商品を返品し、その全額の返金を受けることができます。 全額返金ポリシーを見る

製品コンプライアンスの詳細

以下に概説されているこの製品に固有のコンプライアンス情報を参照してください。

以下の情報は、この製品を販売する独立したサードパーティ小売業者によって提供されています。

製造業者:
次の情報は、Fruugoで販売される関連製品の製造業者の連絡先詳細です。

  • Wuhan Pinsheng Technology Co., Ltd.
  • Wuhan Pinsheng Technology Co., Ltd.
  • No.A357,Shoulder-to-shoulder?Incubator,Building?4
  • Wuchang District
  • Wuhan
  • CN
  • 430000
  • pinsenkj@163.com
  • 18062524796
  • https://shop01473o1711614.1688.com/page/creditdetail.htm?spm=a261y.7663282.shopNavigation.1.6310755czE9SFQ

EUにおける責任者:
次の情報は、EUにおける責任者の連絡先情報の概要です。ここで言う責任者とはEUに拠点を置く指定経済事業者で、EU域内で販売される関連製品に関するコンプライアンス義務を負う者のことです。

  • None
  • Kequ Technology s.r.o.
  • Pražákova 1008/69
  • Štýřice
  • Jihomoravský kraj
  • Brno
  • CZ
  • 63900
  • christopher25106@outlook.com
  • 420608214795