Feature:1. Fitment: The OBD2 engine fault code reader is applicable replacement for MercedesBenz W211 R230 with for SBC systems, which can be easily repaired without replace the new control module.2. Function: Can scan car diagnostic trouble codes in seconds to pinpoint emission related issues, read, clear codes, view DTC definition, turn off check engine light, check I/M readiness status, retrieve freeze frame data and vehicle information.3. High Efficiency: Retrieve generic codes, manufacturer specific codes, and pending codes in seconds and display DTC definitions under the codes, quickly locating the problem areas, then clear or reset the codes after proper repairs.4. Easy to Use: Each code is followed by its definition, saving time and effort, quickly locating the problem location, perfect for car DIYers and beginners. When you are reading codes, the corresponding DTC definition is placed below the code.5. Operation: Plug in the OBDII communication port, turn on the ignition switch, call twice to indicate that the device is working normally, restore the maintenance mode switch when the BUSY indicator is on, and complete the data recovery after 10 seconds.Specification:Item Type: OBD2 Scanner.Material: ABSOperation Steps:2. Turn the ignition switch to ON, then power light lit, and the device will call and the second tone, said the device is working properly;3. Then you need to restore the maintenance mode switch (25% -50% -75% -100% can be selected) at this time there will be frequency BUSY indicator light, and the device will beep tones, 10 seconds to complete data recovery, the BUSY LED is on constantly.Replacement for MercedesBenz W211 R230 with ABS for SBC systemTIPS: CODE C249F, OPERATION TIME OF COMPONENT A7/3 IS EXCEEDED ( for SBC HYDRAULIC UNIT)The above tips that show internal fault of control unit, you have to replace the for SBC control module and using W211 R230 TOOL that can be easily repaired without replace the new control module.Replacement for MercedesBenz's Safety Precautions had stated that before attempting to repair the brake system on its models W211 E Class and R230 SL Class, the Sensotronic Brake Control (for SBC) system must be deactivated first using its STAR-DIAGNOSIS tester. Deactivation of the for SBC system is absolutely necessary before carrying out any maintenance work on the brakes like changing of pads, discs and fluids because the system is under a pressure of 140 bars. Mechanics who perform brake services on these car models must have the proper tools to avoid the risk of injuries to themselves and damage to the brake system. Until the introduction of this inexpensive, convenient, light, safe and easy to use for SBC tool is another alternative to the STAR-DIAGNOSIS tester when working on for SBC system. It can perform the tasks equally well which is efficient and safety. After the repair had done, the for SBC system can be activated and restore back its pressure. The memory is erased automatically. Advantage:Quick, easy operations with LED indications.Safe to usePower ON when plugged into vehicle's OBDII diagnostic connector.Compact and very convenient.Stand alone unit This for SBC tool works on for W211 E-Class and R230 SL-Class with for SBC systems. It is ideally suited for:Brake centersIndependent replacement for MercedesBenz workshopsTire Service centersService garagesQuick service centersReplacement for MercedesBenz Specialist centersAutomotive Repair Workshops for SBC TOOL Support Type:Replacement for BOSCH NR: 0 265 960 012Replacement for BOSCH NR: 0 265 960 013Replacement for BOSCH NR: 0 265 960 015Replacement for BOSCH NR: 0 265 960 018Replacement for BOSCH NR: 0 265 960 019Replacement for BOSCH NR: 0 265 960 020Replacement for BOSCH NR: 0 265 960 023Replacement for BOSCH NR: 0 265 960 025Replacement for BOSCH NR: 0 265 960 028Package List:1 xOBD2 Scanner1 x Manual